根據提示安裝聲卡，但進行make config時

wyk6000

根據提示安裝聲卡，但.進行到第７步時敲入make config提示
make:*** NO rule to make targer 'config''.  Stop
不知如何處理，謝謝







以下是安裝提示：
Driver and Software for Linux


Driver and software for Linux. You can using our Sound Track Series under Linux.
You can download this files under Download area. This Driver and software working with our ISA sound card series. We will release Linux Driver and software for PCI series.

Note : This driver and program is developed by Jae-Hyun Kim dolbbi@soback.kornet.nm.kr Thanks to Jae-Hyun Kim.

Download Software

1. unzip linuxdrv.zip file.
2. move cs4237.tgz file to /usr/src/linux/drivers/sound/
3. move soundcard.hgz file to /usr/src/linux/include/linux and unzip file.
4. Command "/usr/src/linux/drivers/sound/"
5. Command "gzip -d"
6. Command "tar xvf cs4237.tar"
Note : This files are not patch files.
This files maked under kernel 2.0.31
7. Command make config
8. Assign the module cs4237, mpu401 and OPL. Don't assign WSS/MSS or SB.
Note : If you assign cs4237, pls refer /windows/cwbaudio.wcm or /windows/cwbaudio.ini file.
9. command "make dep;make clean;make modules;make modules_install"
10. Confirm whether driver installed properly. Command "cat /dev/sndstat"
11. Follows screen will be appear, if driver installed properly

Note : IRQ, DRQ, CTRL may not matched.



Config options: 0

Installed drivers:


Type 27: CS4237
Type 28: CS4237 MIDI
Type 1: OPL-2/OPL-3 FM
Type 5: Roland MPU-401

Card config:


(CS4237 MIDI at 0x338 irq 7 drq 0)
CS4237 at 0x534 irq 7 drq 1,0 ctrl 0x120
Roland MPU-401 at 0x330 irq 11 drq 0
OPL-2/OPL-3 FM at 0x388 drq 0

Audio devices:


0: CS4237 (CS4237B) (DUPLEX)

Synth devices:


0: Yamaha OPL-3

Midi devices:


0: MPU-401 0.0 Midi interface #1

Timers:


0: System clock
1: CS4237 (CS4237B)

Mixers:


0: CS4237 (CS4237B)

Made by Jae-Hyun Kim(dolbbi@soback.kornet.nm.kr)



Excutor files for Sound Track 97/128 ISA series.

We release excutor files for Sound Track 97/128 ISA series. We will release kernel version soon.

1. Assing module (refer readme1.txt)
2. Run PnP97set shell scriptor for PNP setting
3. Run 97dinit for firmware downloading
4. Run load font for bank downloading
5. Run mixer

1. pnp97set


- pnp97set will run setpnp97 by shell scriptor.
setpnp97 has follows options.
Note : Pls refer c:/windows/cwbaudio.ini or c:/windows/cwbaudio.wcm
/L0=WssIO,OplIO,SbIO,WssInt,WssDmaPlay,WssDmaCapture
/L1=GameIO ( We recommand /L1=B376)
/L2=4232IO
/L3=CDIO,CDInt
/L4=RAM,MIDI,DAAD,DAC
->; RAM Size ( 0:4M(32M), 1:16M )
MIDI ( 0:Crystal, 1ream )
DAAD ( 0:Crystal, 1:Ext Daad )
DAC Source ( 0:Crystal, 1:MIC, 2:Line IN 1, 3:Line IN 2)

I.E) cwbaudio.ini
[PNP]
WssIO=534
WssInt=7
WssDmaPlay=1
WssDmaCapture=0
SbIO=220
OplIO=388
OplInt=Disabled

GameIO=200

4232IO=538
4232Int=Disabled

MPU401IO=320
MPU401Int=Disabled

CDIO=330
CDInt=11
CDDma=Disabled

I.E) If RAM is 16MB, MIDI is DREAM, DAAD is Crystal, DAC Source Crystal, PNP setting is as like follows
setpnp97 /V/O/L0=B534B388B220I7D1D0/L1=B376/L2=B538/L3=B320/L4=B330I11/ID=CSC4637/SN=FFFFFFFF
/DA=1100

2. 94dinit


94dinit downlaod firmware and initial sound card. If you run 94dinit, you have to down load bank.
!! Note: setpnp97 have to be run before run 94dinit

I.E)
94dinit F=hoonx44b.bin

-- 3. loadfont
!! Note: You have to remove sound module for using loadfont (rmmod sound)
I.E)
loadfont mu80.94b

-- 4. mxset97
I.E)
mxset97 default.mix

You may use aumix to adjust volume.
You have to use -e option in playmidi for using dream MIDI.
I.E) playmidi -e sp32xg.mid