雙網卡bond1的配置問題

yurenyahe

雙網卡BOND1測試，當前活動網卡在ETH2時可以正常，切到ETH3時網絡不通是什么問題？

環境描述：

1、VMWARE虛擬機，雙網卡，ifcfg-eth2、ifcfg-eth3、ifcfg-bond0，VMWARE網絡為“僅主機”

2、配置如下：

網卡ifcfg-eth2配置：

DEVICE=eth2
BOOTPROTO=none
ONBOOT=yes
TYPE=Ethernet
USERCTL=no
MASTER=bond0
SLAVE=yes

網卡ifcfg-eth3配置：

DEVICE=eth3
BOOTPROTO=none
ONBOOT=yes
USERCTL=no
MASTER=bond0
SLAVE=yes

ifcfg-bond0

DEVICE=bond0
ONBOOT=yes
BOOTPROTO=static
IPADDR=192.168.222.105
BROADCAST=192.168.222.255
NETMASK=255.255.255.0
GATEWAY=192.168.222.101
DNS1=192.168.222.104
USERCTL=no
TYPE=Ethernet
BONDING_OPTS="mode=1 miimon=200"

以下是bond0的狀態情況，是可以實現自動切換，但切到eth3網絡就不通了。

[root@client /]# cat /proc/net/bonding/bond0
Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)

Bonding Mode: fault-tolerance (active-backup)
Primary Slave: None
Currently Active Slave: eth2
MII Status: up
MII Polling Interval (ms): 200
Up Delay (ms): 0
Down Delay (ms): 0

Slave Interface: eth2
MII Status: up
Speed: 1000 Mbps
Duplex: full
Link Failure Count: 0
Permanent HW addr: 00:00:00:00:65:99
Slave queue ID: 0

Slave Interface: eth3
MII Status: up
Speed: 1000 Mbps
Duplex: full
Link Failure Count: 0
Permanent HW addr: 00:00:00:00:65:a3
Slave queue ID: 0

[root@client modprobe.d]# cat /etc/modprobe.d/bonding.conf
alias bond0 bonding

[root@client rc.d]# cat /etc/rc.d/rc.local
ifenslave bond0 eth2 eth3

[root@client rc.d]# ip link
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: eth2: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master bond0 state UP qlen 1000
    link/ether 00:00:00:00:65:99 brd ff:ff:ff:ff:ff:ff
3: eth3: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master bond0 state UP qlen 1000
    link/ether 00:00:00:00:65:a3 brd ff:ff:ff:ff:ff:ff
4: bond0: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP
    link/ether 00:00:00:00:65:99 brd ff:ff:ff:ff:ff:ff