- 論壇徽章:
- 0
|
系統(tǒng)進去了，也改過來了，多謝，但還有些啟動報錯，幫看一下。
-Boot 1.1.1
custom Sun Microsystems U-Boot 1.3 (Oct 29 2010 - 18:42:02) r59946
CPU: MPC885ZPnn at 133 MHz: 8 kB I-Cache 8 kB D-Cache FEC present
Board: SPARC885
Watchdog enabled
I2C: ready
DRAM:
trying 128 MBytes
(128 MB SDRAM) 128 MB
Memory Tests: DA A1 A2 00 FF 55 AA T2 T3 T4
POST memory PASSED
FLASH: 32 MB
In: serial
Out: serial
Err: serial
Net: FEC ETHERNET
POST i2c c d 18 20 23 2a 2d 2e 30 40 43 46 51 53 54 56 68 69 6a 6b 70 71 PASSED
POST cpu PASSED
POST ethernet PASSED
Booting linux in 5 seconds...
## Booting image at fe080000 ...
Image Name: Linux-2.4.22
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 814599 Bytes = 795.5 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
do_bootm_linux():
argv[0]=bootm
argv[1]=0xfe080000
## Current stack ends at 0x07D38B60 => set upper limit to 0x00800000
No initrd
## cmdline at 0x007FFF00 ... 0x007FFF80
memstart = 0x00000000
memsize = 0x08000000
flashstart = 0xFE000000
flashsize = 0x02000000
flashoffset = 0x0004C000
sramstart = 0x00000000
sramsize = 0x00000000
EnvAddr = 0xF2BE2F4D
EnvSize = 0xA66E4F37
banksize = 0x02000000
banks = 0x00000001
bankwidth = 0x00000001
sectorsize = 0x00020000
sectorcount = 0x00000100
booted = 0xFE080000
boottype = 0x00000000
primary = 0xFFFFFFFF
pritype = 0x00000000
secondary = 0xFFFFFFFF
sectype = 0x00000000
image0 = 0xFE000000
image1 = 0xFF000000
maximage = 0x01000000
immr_base = 0xF0000000
bootflags = 0x00000001
intfreq = 133 MHz
busfreq = 66.500 MHz
ethaddr = 00:21:28:C1:A1:97
IP addr = 0.0.0.0
baudrate = 9600 bps
## Transferring control to Linux (at address 00000000) ...
## parameters(007ffe80,00000000,00000000,007fff00,007fff80)
Linux version 2.4.22 (cb75630@sanpen-rh5-0) (gcc version 3.3.4) #2 Fri Oct 29 18:37:31 PDT 2010 r59948
On node 0 totalpages: 32768
zone(0): 32768 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock4 rootfstype=squashfs ro mtdparts=phys:384K(u1),128k(e1),1536K(k1),14M(r1),384K(u2),128K(e2),1536K(k2),14M(r2)
Decrementer Frequency = 498750000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x12C0)
Calibrating delay loop... 132.71 BogoMIPS
Memory: 127624k available (1412k kernel code, 416k data, 68k init, 0k highmem)
Dentry cache hash table entries: 16384 (order: 5, 131072 bytes)
Inode cache hash table entries: 8192 (order: 4, 65536 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 8192 (order: 3, 32768 bytes)
Page-cache hash table entries: 32768 (order: 5, 131072 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Journalled Block Device driver loaded
squashfs: version 3.0 (2006/03/15) Phillip Lougher
JFFS2 version 2.1. (C) 2001 Red Hat, Inc., designed by Axis Communications AB.
CPM UART driver version 0.03
ttyS00 at 0x0100 is apty: 256 Unix98 ptys configured
Generic RTC Driver v1.07
eth0: FEC ENET Version 0.2, FEC irq 3, MII irq 6, addr 00:21:28:c1:a1:97
RAMDISK driver initialized: 16 RAM disks of 18432K size 1024 blocksize
eth0: Phy @ 0x0, type DM9161 (0x0181b881)
loop: loaded (max 8 devices)
physmap flash device: 2000000 at fe000000
Amd/Fujitsu Extended Query Table v1.3 at 0x0040
number of CFI chips: 1
Using command line partition definition
Creating 8 MTD partitions on "Physically mapped flash":
mtdblock1: 0x00000000-0x00060000 : "u1"
mtdblock2: 0x00060000-0x00080000 : "e1"
mtdblock3: 0x00080000-0x00200000 : "k1"
mtdblock4: 0x00200000-0x01000000 : "r1"
mtdblock5: 0x01000000-0x01060000 : "u2"
mtdblock6: 0x01060000-0x01080000 : "e2"
mtdblock7: 0x01080000-0x01200000 : "k2"
mtdblock8: 0x01200000-0x02000000 : "r2"
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
i2c-rpx.o: i2c MPC8xx module version 2.6.1 (20010830)
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP: Hash tables configured (established 8192 bind 16384)
ip_conntrack version 2.1 (1024 buckets, 8192 max) - 292 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
ipt_recent v0.3.1: Stephen Frost <sfrost@snowman.net>. http://snowman.net/projects/ipt_recent/
arp_tables: (C) 2002 David S. Miller
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 68k init
modprobe: modprobe: Can't open dependencies file /lib/modules/2.4.22/modules.dep (No such file or directory)
Creating /var tmpfs
Creating directories in /var...done.
Creating /var/log tmpfs...done.
Activating swap.
Calculating module dependencies... done.
Loading modules...
fpga
Warning: loading /lib/modules/2.4.22/misc/fpga/fpga.o will taint the kernel: non-GPL license - Proprietary
See http://www.tux.org/lkml/#export-tainted for information about tainted modules
Platform ID : 1
Minor revision : 0
Major revision : 5
FPGA power status : 80
(SYS_POK_EN !DC_POK !POK_OIO !POK_VMEMR !POK_VMEML !POK_VCORE !POK_PSU1 !POK_PSU0 )
BR2: 0xf2000000/0x1000000/0xf2000401/0xff0001fc
FPGA init OK: base f2000000, size 1000000 (major 120)
Module fpga loaded, with warnings
fpga_flash
Warning: loading /lib/modules/2.4.22/misc/fpga_flash/fpga_flash.o will taint the kernel: no license
See http://www.tux.org/lkml/#export-tainted for information about tainted modules
Module fpga_flash loaded, with warnings
immap
Warning: loading /lib/modules/2.4.22/misc/immap/immap.o will taint the kernel: no license
See http://www.tux.org/lkml/#export-tainted for information about tainted modules
Module immap loaded, with warnings
All modules loaded.
Checking all file systems...
fsck (busybox 1.9.0, 2010-10-29 18:42:30 PDT)
Setting kernel variables ...
kernel.core_pattern = /coredump/%h.%e.core
kernel.core_uses_pid = 1
net.ipv4.ip_local_port_range = 3100 7075
... done.
Mounting local filesystems...
Identifying DOC Device Type(G3/G4/H3) ...
Warning: /lib/modules/2.4.22/misc/tffs/tffs_h3.o symbol for parameter prio not found
Warning: loading /lib/modules/2.4.22/misc/tffs/tffs_h3.o will taint the kernel: non-GPL license - Proprietary
See http://www.tux.org/lkml/#export-tainted for information about tainted modules
tffs: TrueFFS driver 7100.76
tffs: will not use IRQ
tffs: Looking for G4/P4 MDOC Devices while assuming IF_CFG=16.
tffs: Looking for G4/P4 MDOC Devices while assuming IF_CFG=8.
tffs: Flow: G4_docWindowBaseAddress Exit (NOT FOUND).
tffs: Looking for G3/P3 MDOC Devices while assuming IF_CFG=16.
tffs: Looking for G3/P3 MDOC Devices while assuming IF_CFG=8.
tffs: Looking for H1 DOC at address 0xcd14e000
tffs: DOCH found
tffs: Socket 0 in addr 0xf4000000
tffs: Device 0x0: size 0x1db00000 HW sector 0x200 (recommended 0x1000)
tffs: use major device number 100
Partition check:
tffsa: tffsa1 tffsa2 tffsa3
tffs: disk partition: dev_number=0x6401, 65534 sectors, start_sector=1
tffs: disk partition: dev_number=0x6402, 65536 sectors, start_sector=65535
tffs: disk partition: dev_number=0x6403, 112000 sectors, start_sector=131071
Module tffs_h3 loaded, with warnings
Loaded TFFS kernel module /lib/modules/2.4.22/misc/tffs/tffs_h3.o
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS 2.4-0.9.19, 19 August 2002 on tffs(100,1), internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS 2.4-0.9.19, 19 August 2002 on loop(7,0), internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS 2.4-0.9.19, 19 August 2002 on loop(7,1), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS 2.4-0.9.19, 19 August 2002 on loop(7,2), internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS 2.4-0.9.19, 19 August 2002 on loop(7,3), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS 2.4-0.9.19, 19 August 2002 on loop(7,4), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS 2.4-0.9.19, 19 August 2002 on tffs(100,3), internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
Mounted all disk partitions.
Checking configuration files state ...
Image date: Fri Oct 29 20:00:37 PDT 2010 Image revision: 59946
Conf date: Fri Oct 29 20:00:37 PDT 2010 Conf revision: 59946
Configuration files state good after upgrade.
Loaded IFC configuration file.
Created links for vbsc
Running ldconfig...done
Setting the System Clock using the Hardware Clock as reference...
System Clock set. Local time: Sun May 15 22:54:38 GMT 2016
Setting up networking...done.
Hostname: ORACLESP-BDL1118058.
Setting up IP spoofing protection: rp_filter.
Configuring IPv6...done
Configuring network interfaces...done.
Starting portmap daemon: portmap.
Initializing random number generator...done.
Incrementing bootcount ... done (23)
populating memstore vars from disk
INIT: Entering runlevel: 3
Preparsing sensor.xml...
Starting system log daemon: syslogd and klogd.
Starting capidirect daemon: Done
Starting Boot Timer.
Starting user mgmt upgrade program: usrmgt_upgrade.
Starting the Health Monitor Daemon...
Starting portmap daemon: portmap.
Starting capidirectd: Done.
Starting Network Interface Plugging Daemon: eth0.
Starting IPMI Stack...... Done.
SSH RSA Host Key Files already exist. Skipping key creation ...
SSH DSA Host Key Files already exist. Skipping key creation ...
Starting sshd.
Starting BBR daemon...
bbrd started after 1 seconds.
Starting periodic command scheduler: cron.
Starting Serial Server :seriald .
Starting Servicetags discoverer: stdiscoverer.
Starting Servicetags listener: stlistener.
|
|
免費注冊
發(fā)表于 2016-05-12 16:46
發(fā)表于 2016-05-16 10:37