亚洲av成人无遮挡网站在线观看,少妇性bbb搡bbb爽爽爽,亚洲av日韩精品久久久久久,兔费看少妇性l交大片免费,无码少妇一区二区三区

  免費注冊 查看新帖 |

Chinaunix

  平臺 論壇 博客 文庫
最近訪問板塊 發新帖
查看: 2927 | 回復: 9
打印 上一主題 下一主題

我的CISCO3600板子是不是燒了? [復制鏈接]

論壇徽章:
0
跳轉到指定樓層
1 [收藏(0)] [報告]
發表于 2003-02-24 18:34 |只看該作者 |倒序?yàn)g覽
CISCO3600, 配置了兩個模塊,一個模塊上帶一個100M Ethernet接口,另一個模塊上帶4個serial口,

一次斷電后重啟, 發現帶4個serial口的模塊丟失了, show start情況一切正常, show run則只剩下Ethernet口的信息,執行copy start run報錯"interface ^Serial1/1 % Invalid input detected at '^' marker."意思是serial1/1口不存在.

另外每個serial口下都有5個狀態指示燈:CN/LP, RXC, RXD, TXC, TXD,每個serial口的RXC,TXC都常亮.

重啟,重配置均不能識別serial口,請教該模塊是不是在斷電時燒了?有辦法讓系統重新識別帶4個serial口的該模塊嗎?

論壇徽章:
0
2 [報告]
發表于 2003-02-24 19:19 |只看該作者
提示: 作者被禁止或刪除 內容自動屏蔽

論壇徽章:
0
3 [報告]
發表于 2003-02-24 23:05 |只看該作者

我的CISCO3600板子是不是燒了?

敬請指正,不勝感激。。!

Router#show ver
Cisco Internetwork Operating System Software
IOS (tm) 3600 Software (C3620-I-M), Version 12.2(1a), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2001 by cisco Systems, Inc.
Compiled Fri 25-May-01 23:54 by pwade
Image text-base: 0x60008950, data-base: 0x60A34000

ROM: System Bootstrap, Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE SOFTWARE (f
c1)

Router uptime is 5 hours, 18 minutes
System returned to ROM by reload
System image file is "flash:c3620-i-mz.122-1a.bin"

cisco 3620 (R4700) processor (revision 0x81) with 28672K/4096K bytes of memory.
Processor board ID 22788956
R4700 CPU at 80Mhz, Implementation 33, Rev 1.0
Bridging software.
X.25 software, Version 3.0.0.
1 FastEthernet/IEEE 802.3 interface(s)
DRAM configuration is 32 bits wide with parity disabled.
29K bytes of non-volatile configuration memory.
8192K bytes of processor board System flash (Read/Write)

Configuration register is 0x2142

Router#show controllers
Interface FastEthernet0/0
Hardware is AMD Laguna
ADDR: 6111EEE0, FASTSEND: 6002F908, MCI_INDEX: 0
DIST ROUTE ENABLED: 0
Route Cache Flag: 0
LADRF=0x0000 0x0100 0x0000 0x0000
CSR0  =0x00000004, CSR3  =0x00001044, CSR4  =0x00004915, CSR15 =0x00000180
CSR80 =0x00009900, CSR114=0x00000000, CRDA  =0x01D18720, CXDA  =0x01D18B60
BCR9 =0x00000000 (half-duplex)
CSR5  =0x00000000, CSR7  =0x00008820, CSR100=0x0000F000, CSR125=0x00005C3C
BCR2  =0x00000000, BCR9  =0x00000000, BCR18 =0x000019E0, BCR22 =0x0000FF06
BCR25 =0x000000FF, BCR26 =0x00000080, BCR27 =0x00000010, BCR32 =0x00004080
HW filtering information:
  Promiscuous Mode Disabled, PHY Addr Enabled, Broadcast Addr Enabled
  PHY Addr=0004.4DCB.D3A0, Multicast Filter=0x0000 0x0100 0x0000 0x0000
amdp2_instance=0x6111E734, registers=0x3C000000, ib=0x1D186C0
rx ring entries=64, tx ring entries=128
rxring=0x1D18720, rxr shadow=0x6111E944, rx_head=0, rx_tail=0
txring=0x1D18B60, txr shadow=0x61120B98, tx_head=0, tx_tail=0, tx_count=0
Software MAC address filter(hash:length/addr/mask/hits):
  0xC0:  0  0100.0ccc.cccc  0000.0000.0000         0
spurious_idon=0, filtered_pak=0, throttled=0, enabled=0, disabled=0
rx_framing_err=0, rx_overflow_err=0, rx_buffer_err=0
rx_bpe_err=0, rx_soft_overflow_err=0, rx_no_enp=0, rx_discard=0
tx_one_col_err=0, tx_more_col_err=0, tx_no_enp=0, tx_deferred_err=0
tx_underrun_err=0, tx_late_collision_err=0, tx_loss_carrier_err=0
tx_exc_collision_err=0, tx_buff_err=0, fatal_tx_err=0
hsrp_conf=0, need_af_check=0
tx_limited=0(64)
PHY registers:
  Register 0x00:   1400  784B  2000  5C01  01E1  0000  0000  0000
  Register 0x08:   0000  0000  0000  0000  0000  0000  0000  0000
  Register 0x10:   0000  0000  0000  0000        0000  0001  8060
  Register 0x18:   8020  0800  0000  3800  A3B9

Router#

論壇徽章:
0
4 [報告]
發表于 2003-02-24 23:16 |只看該作者

我的CISCO3600板子是不是燒了?

另附系統信息如下:

Router#show start
Using 934 out of 30712 bytes
!
version 12.2
no service single-slot-reload-enable
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname Router
!
logging rate-limit console 10 except errors
enable secret 5 $1$Z/7P$XcTGP9ZT6ru5DBalSrdrN.
enable password cisco
!
ip subnet-zero
no ip routing
!
!
no ip finger
!
no ip dhcp-client network-discovery
!
!
!
interface FastEthernet0/0
ip address 162.105.166.7 255.255.254.0
no ip route-cache
duplex auto
speed auto
!
interface Serial1/0
ip address 162.105.103.1 255.255.255.0
no ip route-cache
!
interface Serial1/1
no ip address
no ip route-cache
shutdown
!
interface Serial1/2
no ip address
no ip route-cache
shutdown
!
interface Serial1/3
no ip address
no ip route-cache
shutdown
!
ip classless
ip route 162.105.164.0 255.255.255.0 162.105.103.2
no ip http server
!
!
line con 0
transport input none
line aux 0
line vty 0 4
password cisco
login
!
end

Router#show run
Building configuration...

Current configuration : 685 bytes
!
version 12.2
no service single-slot-reload-enable
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname Router
!
logging rate-limit console 10 except errors
enable secret 5 $1$Z/7P$XcTGP9ZT6ru5DBalSrdrN.
enable password cisco
!
ip subnet-zero
no ip routing
!
!
no ip finger
!
no ip dhcp-client network-discovery
!
!
interface FastEthernet0/0
ip address 162.105.166.7 255.255.254.0
no ip route-cache
no ip mroute-cache
shutdown
duplex auto
speed auto
!
ip classless
ip route 162.105.164.0 255.255.255.0 162.105.103.2
no ip http server
!
!
line con 0
transport input none
line aux 0
line vty 0 4
password cisco
login
!
end

Router#copy start run
Destination filename [running-config]?
interface Serial1/0
          ^
% Invalid input detected at '^' marker.

ip address 162.105.103.1 255.255.255.0
           ^
% Invalid input detected at '^' marker.

no ip route-cache
            ^
% Invalid input detected at '^' marker.

interface Serial1/1
          ^
% Invalid input detected at '^' marker.

no ip address
% Incomplete command.

no ip route-cache
            ^
% Invalid input detected at '^' marker.

shutdown
  ^
% Invalid input detected at '^' marker.

interface Serial1/2
          ^
% Invalid input detected at '^' marker.

no ip address
% Incomplete command.

no ip route-cache
            ^
% Invalid input detected at '^' marker.

shutdown
  ^
% Invalid input detected at '^' marker.

interface Serial1/3
          ^
% Invalid input detected at '^' marker.

no ip address
% Incomplete command.

no ip route-cache
            ^
% Invalid input detected at '^' marker.

shutdown
  ^
% Invalid input detected at '^' marker.

934 bytes copied in 1.472 secs (934 bytes/sec)
Router#

論壇徽章:
0
5 [報告]
發表于 2003-02-25 11:50 |只看該作者

我的CISCO3600板子是不是燒了?

這種情況,我們碰到過,首先查接地是否很好,再有換一塊好的串口模塊,開機正常后,再插上這塊懷疑有問題的模塊,最好用手下摸一下模塊以放靜電,重啟可能就好了.

論壇徽章:
0
6 [報告]
發表于 2003-02-25 12:09 |只看該作者

我的CISCO3600板子是不是燒了?

已經保證良好接地了,但故障依舊......

論壇徽章:
0
7 [報告]
發表于 2003-02-25 12:26 |只看該作者

我的CISCO3600板子是不是燒了?

Configuration register is 0x2142 改成0x2102試一下

論壇徽章:
0
8 [報告]
發表于 2003-02-25 13:31 |只看該作者

我的CISCO3600板子是不是燒了?

改成了0x2102重啟還是依然,反復拔插3600上的兩個模塊,現在連原來正常的Ethernet口模塊也出現了一樣的情況,也不認了,不過可以根據此情況基本上判斷應該不是燒板子,不會這么容易被燒吧.

另外,發現啟動時報錯如下:
Smart Init is enabled
smart init is sizing iomem
  ID            MEMORY_REQ                 TYPE
000000           UNKNOWN port adapter
00FFFF           UNKNOWN port adapter
                0X0010A6F8 public buffer pools
                0X00211000 public particle pools
TOTAL:          0X0031B6F8

If any of the above Memory Requirements are
"UNKNOWN", you may be using an unsupported
configuration or there is a software problem and
system operation may be compromised.
Rounded IOMEM up to: 4Mb.
Using 12 percent iomem. [4Mb/32Mb]

請問大俠們還有好辦法嗎?

論壇徽章:
0
9 [報告]
發表于 2003-02-25 15:49 |只看該作者

我的CISCO3600板子是不是燒了?

sh  diag 看看結果。一般情況板子不容易壞的

論壇徽章:
0
10 [報告]
發表于 2003-02-25 16:59 |只看該作者

我的CISCO3600板子是不是燒了?

現在的問題奇怪了,兩個模塊都出現同樣的問題了,報告如下,但若把有問題的那個模塊撤掉,則原來正常的模塊就會恢復正常.....,..
Router#show diag
Slot 0:
        Unknown (type 0) Port adapter
        Port adapter is disabled
        Port adapter insertion time unknown
        EEPROM contents at hardware discovery:
        Hardware revision 255.252               Board revision UNKNOWN
        Serial number     0             Part number    00-0255-252
        Test history      0x0           RMA number     00-00-00
        EEPROM format version 0
        EEPROM contents (hex):
          0x20: 00 00 FF FC 00 00 00 00 00 00 FF FC 00 00 00 00
          0x30: 00 00 FF FC 00 00 00 00 00 00 FF FC 00 00 00 00

Slot 1:
        Unknown (type 0) Port adapter
        Port adapter is disabled
        Port adapter insertion time unknown
        EEPROM contents at hardware discovery:
        Hardware revision 255.252               Board revision UNKNOWN
        Serial number     0             Part number    00-0255-252
        Test history      0x0           RMA number     00-00-00
        EEPROM format version 0
        EEPROM contents (hex):
          0x20: 00 00 FF FC 00 00 00 00
          0x30: 00 00 FF FC 00 00 00 00 00 00 FF FC 00 00 00 00
        Current EEPROM contents:
        EEPROM format version 255
        EEPROM contents (hex):
          0x00: FF FF 01 00 01 51 36 E5 50 04 C8 02 00 00 00 00
          0x10: 88 52 69 00 00 10 17 17 FF FF FF FF FF FF FF FF
          0x20: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x30: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
撤掉有問題的模塊后再看:
outer#show diag
Slot 0:
        Fast-ethernet Port adapter, 1 port
        Port adapter is analyzed
        Port adapter insertion time unknown
        EEPROM contents at hardware discovery:
        Hardware revision 1.0           Board revision H0
        Serial number     21440534      Part number    800-03490-02
        Test history      0x0           RMA number     00-00-00
        EEPROM format version 1
        EEPROM contents (hex):
          0x20: 01 44 01 00 01 47 28 16 50 0D A2 02 00 00 00 00
          0x30: 88 00 00 00 00 07 28 00 FF FF FF FF FF FF FF FF
您需要登錄后才可以回帖 登錄 | 注冊

本版積分規則 發表回復

  

北京盛拓優訊信息技術有限公司. 版權所有 京ICP備16024965號-6 北京市公安局海淀分局網監中心備案編號:11010802020122 niuxiaotong@pcpop.com 17352615567
未成年舉報專區
中國互聯網協會會員  聯系我們:huangweiwei@itpub.net
感謝所有關心和支持過ChinaUnix的朋友們 轉載本站內容請注明原作者名及出處

清除 Cookies - ChinaUnix - Archiver - WAP - TOP