求救:L3000錯誤代碼分析

key_1

期待高手!!!

feng551

你把其他硬盤全部把出，把os盤放在disk0位置，然后開機，sea后看到硬盤，bo下 ，能否進入系統，如果順利進入系統，那重新shutdown -ry 0下，應該自動啟動為disk0

fly_sky418

貼上 MAIN MENU: ser -> scsi  信息

key_1

---
Service Menu: Enter command > scsi

Path (dec)     Initiator ID     SCSI Rate     Auto Term
------------   --------------   ----------    ---------------
0/0/1/0        7                Ultra         Unknown
0/0/1/1        7                Ultra         Unknown
0/0/2/0        7                Ultra         Unknown

key_1

只留一塊硬盤在A0插槽,查找硬盤啟動系統:
Main Menu: Enter command or menu > sea

Searching for potential boot device(s)
This may take several minutes.

To discontinue search, press any key (termination may not be immediate).


                                                                           IODC
   Path#  Device Path (dec)  Device Path (mnem)  Device Type               Rev
   -----  -----------------  ------------------  -----------               ----
   P0     0/0/2/0.0          intscsia.0          Random access media       1
   P1     0/0/2/1.0                              Random access media       1


Main Menu: Enter command or menu > bo
Interact with IPL (Y, N, or Cancel)?> n

Booting...
Boot IO Dependent Code (IODC) revision 1


HARD Booted.

ISL Revision A.00.43  Apr 12, 2000

ISL booting  hpux

Boot
: disk(0/0/2/0.0.0.0.0.0.0;0)/stand/vmunix
8212480 + 1617920 + 1278368 start 0x1eb868




alloc_pdc_pages: Relocating PDC from 0xffff800000 to 0x3fb01000.
gate64: sysvec_vaddr = 0xc0002000 for 2 pages
NOTICE: nfs3_link(): File system was registered at index 3.
NOTICE: autofs_link(): File system was registered at index 6.
NOTICE: cachefs_link(): File system was registered at index 7.

    System Console is on the Built-In Serial Interface
Entering cifs_init...
Initialization finished su
************* SYSTEM ALERT **************
SYSTEM NAME: uninitialized
DATE: 02/28/2008 TIME: 06:58:50
ALERT LEVEL: 12 = Software failure

REASON FOR ALERT
SOURCE: 1 = processor
SOURCE DETAIL: 1 = processor general   SOURCE ID: 0
PROBLEM DETAIL: 0 = no problem detail

LEDs:  RUN      ATTENTION     FAULT     REMOTE     POWER
       FLASH    OFF           OFF       OFF        ON
LED State: Running non-OS code. (i.e. Boot or Diagnostics)

0xF8E000C01100B800 00000000 0000B800 - type 31 = legacy PA HEX chassis-code
0x58E008C01100B800 00006C01 1C063A32 - type 11 = Timestamp 02/28/2008 06:58:50
A: ack read of this entry - X: Disable all future alert messages
Anything else skip redisplay the log entry
->Choice:a

key_1

從光盤引導系統:
Main Menu: Enter command or menu > sea

Searching for potential boot device(s)
This may take several minutes.

To discontinue search, press any key (termination may not be immediate).


                                                                           IODC
   Path#  Device Path (dec)  Device Path (mnem)  Device Type               Rev
   -----  -----------------  ------------------  -----------               ----
   P0     0/0/2/0.0          intscsia.0          Random access media       1
   P1     0/0/2/1.0                              Random access media       1


Main Menu: Enter command or menu > bo p1
Interact with IPL (Y, N, or Cancel)?> n

Booting...
Boot IO Dependent Code (IODC) revision 1


HARD Booted.

ISL Revision A.00.43  Apr 12, 2000

ISL booting  hpux (;0):INSTALL

Boot
: disk(0/0/2/1.0.0.0.0.0.0;0):WINSTALL
8941568 + 1642496 + 2596176 start 0x1fef68




alloc_pdc_pages: Relocating PDC from 0xffff800000 to 0x3fb01000.
引導到此不能往下引導

punish01

根據我的判斷一個可能是CPU0壞了，你將CPU0換了再引導一下試試。如果還CPU0的位置換任何一個CPU還報這個錯誤。那就考慮換主板了。

meixiwang

硬盤沒引導區當燃不能引導 排除光盤問題后用光盤引導到alloc_pdc_pages: Relocating PDC from 0xffff800000 to 0x3fb01000.多等一會這塊時間是比較長的 。

Izumix

從硬盤，到PDC，最后到CPU，連換主板的主義都冒出來了。
拜托，相信大家都是頭頂系統工程師稱號的吧，別整得跟電腦城里賣配件的攤販那樣行不？