亚洲av成人无遮挡网站在线观看,少妇性bbb搡bbb爽爽爽,亚洲av日韩精品久久久久久,兔费看少妇性l交大片免费,无码少妇一区二区三区

Chinaunix

標題: sun T4-1報錯以下錯報 如何處理？ [打印本頁]

作者: lining0925 時間: 2020-01-08 14:30
故障清除后，操作開機后1分鐘就自動巖機了。再查看報錯信息還是一樣

作者: lining0925 時間: 2020-01-08 14:36
哪位大神可以解說一下

作者: cwnlinux 時間: 2020-01-08 15:17
APPLIES TO:

SPARC M7-16
SPARC T7-1
SPARC T7-2
SPARC T7-4
Oracle SuperCluster M7 Hardware
Information in this document applies to any platform.
PURPOSE

Additional Information for SPT-8000-DH - Voltage fail.

DETAILS

Type:

         Fault
         fault.chassis.voltage.fail

Severity:

         Critical

Description

The message ID: SPT-8000-DH indicates that the fault management function running on the service processor has determined that a voltage  is operating outside of the allowable range.
The Chassis service required LED  is illuminated along with the specific FRU if possible..

The specific FRU experiencing the fault can be identified following the procedures described in the document referenced under "Suggested Action for System Administrator".

Automated Response

The system will be powered off. The chassis-wide service required LED will be illuminated.

Impact

The system is not usable until repaired. ILOM will not allow the system to be powered on until repaired.

Suggested Action for System Administrator

The administrator should arrange to have the faulty FRU replaced.

Refer to the following document for the latest procedures for displaying event content in preparation for submitting a service request and applying any post-repair actions that may be required.

作者: lining0925 時間: 2020-01-08 15:44
上樓大哥，意思是除了換主板，就沒別的辦法了？

作者: lining0925 時間: 2020-01-09 15:00
Properties:
      type = Voltage
      ipmi_name = MB/V_+3V3_SLOT
      class = Threshold Sensor
      value = Disabled
      upper_nonrecov_threshold = 3.630 Volts
      upper_critical_threshold = 3.525 Volts
      upper_noncritical_threshold = 3.465 Volts
      lower_noncritical_threshold = 3.165 Volts
      lower_critical_threshold = 3.075 Volts
      lower_nonrecov_threshold = 2.970 Volts
      alarm_status = indeterminate
估計是這個位置壞了。就是不知道這個位置在哪。
正常的主板信息如下Properties:
      type = Voltage
      ipmi_name = MB/V_+3V3_SLOT
      class = Threshold Sensor
      value = 3.270 Volts
      upper_nonrecov_threshold = 3.630 Volts
      upper_critical_threshold = 3.525 Volts
      upper_noncritical_threshold = 3.465 Volts
      lower_noncritical_threshold = 3.165 Volts
      lower_critical_threshold = 3.075 Volts
      lower_nonrecov_threshold = 2.970 Volts
      alarm_status = cleared

歡迎光臨 Chinaunix (http://www.72891.cn/)