亚洲av成人无遮挡网站在线观看,少妇性bbb搡bbb爽爽爽,亚洲av日韩精品久久久久久,兔费看少妇性l交大片免费,无码少妇一区二区三区

Chinaunix

標題: 求助SDS鏡象重啟完后總是有幾個分區需要needs maintenance [打印本頁]

作者: tootooluu 時間: 2006-08-15 19:23
標題: 求助SDS鏡象重啟完后總是有幾個分區需要needs maintenance
ultra 10 機器，solaris 6 + disksuite 4.2，20G硬盤\r\n\r\n 0. c0t0d0 <ST320011A cyl 39533 alt 2 hd 16 sec 63>\r\n /pci@1f,0/pci@1,1/ide@3/dad@0,0\r\n 1. c0t3d0 <ST320420A cyl 39533 alt 2 hd 16 sec 63>\r\n /pci@1f,0/pci@1,1/ide@3/dad@3,0\r\n\r\n做鏡象，做完后同步一切正常，但一重啟動，就會出現某些分區needs maintenance\r\n\r\nd30: Mirror\r\n Submirror 0: d10\r\n State: Okay \r\n Submirror 1: d20\r\n State: Needs maintenance \r\n Pass: 1\r\n Read option: roundrobin (default)\r\n Write option: parallel (default)\r\n Size: 6086304 blocks\r\n\r\nd10: Submirror of d30\r\n State: Okay \r\n Size: 6086304 blocks\r\n Stripe 0:\r\n Device Start Block Dbase State Hot Spare\r\n c0t0d0s0 0 No Okay \r\n\r\n\r\nd20: Submirror of d30\r\n State: Needs maintenance \r\n Invoke: metareplace d30 c0t3d0s0 <new device>\r\n Size: 6086304 blocks\r\n Stripe 0:\r\n Device Start Block Dbase State Hot Spare\r\n c0t3d0s0 0 No Maintenance \r\n\r\n\r\nd31: Mirror\r\n Submirror 0: d11\r\n State: Okay \r\n Submirror 1: d21\r\n State: Okay \r\n Pass: 1\r\n Read option: roundrobin (default)\r\n Write option: parallel (default)\r\n Size: 1049328 blocks\r\n\r\nd11: Submirror of d31\r\n State: Okay \r\n Size: 1049328 blocks\r\n Stripe 0:\r\n Device Start Block Dbase State Hot Spare\r\n c0t0d0s1 0 No Okay \r\n\r\n\r\nd21: Submirror of d31\r\n State: Okay \r\n Size: 1049328 blocks\r\n Stripe 0:\r\n Device Start Block Dbase State Hot Spare\r\n c0t3d0s1 0 No Okay \r\n\r\n\r\nd32: Mirror\r\n Submirror 0: d12\r\n State: Okay \r\n Submirror 1: d22\r\n State: Needs maintenance \r\n Pass: 1\r\n Read option: roundrobin (default)\r\n Write option: parallel (default)\r\n Size: 6291936 blocks\r\n\r\nd12: Submirror of d32\r\n State: Okay \r\n Size: 6291936 blocks\r\n Stripe 0:\r\n Device Start Block Dbase State Hot Spare\r\n c0t0d0s4 0 No Okay \r\n\r\n\r\nd22: Submirror of d32\r\n State: Needs maintenance \r\n Invoke: metareplace d32 c0t3d0s4 <new device>\r\n Size: 6291936 blocks\r\n Stripe 0:\r\n Device Start Block Dbase State Hot Spare\r\n c0t3d0s4 0 No Maintenance \r\n\r\n\r\nd33: Mirror\r\n Submirror 0: d13\r\n State: Okay \r\n Submirror 1: d23\r\n State: Needs maintenance \r\n Pass: 1\r\n Read option: roundrobin (default)\r\n Write option: parallel (default)\r\n Size: 3145968 blocks\r\n\r\nd13: Submirror of d33\r\n State: Okay \r\n Size: 3145968 blocks\r\n Stripe 0:\r\n Device Start Block Dbase State Hot Spare\r\n c0t0d0s5 0 No Okay \r\n\r\n\r\nd23: Submirror of d33\r\n State: Needs maintenance \r\n Invoke: metareplace d33 c0t3d0s5 <new device>\r\n Size: 3145968 blocks\r\n Stripe 0:\r\n Device Start Block Dbase State Hot Spare\r\n c0t3d0s5 0 No Maintenance \r\n\r\n\r\nd34: Mirror\r\n Submirror 0: d14\r\n State: Okay \r\n Submirror 1: d24\r\n State: Okay \r\n Pass: 1\r\n Read option: roundrobin (default)\r\n Write option: parallel (default)\r\n Size: 12583872 blocks\r\n\r\nd14: Submirror of d34\r\n State: Okay \r\n Size: 12583872 blocks\r\n Stripe 0:\r\n Device Start Block Dbase State Hot Spare\r\n c0t0d0s6 0 No Okay \r\n\r\n\r\nd24: Submirror of d34\r\n State: Okay \r\n Size: 12583872 blocks\r\n Stripe 0:\r\n Device Start Block Dbase State Hot Spare\r\n c0t3d0s6 0 No Okay \r\n\r\n\r\nd35: Mirror\r\n Submirror 0: d15\r\n State: Okay \r\n Submirror 1: d25\r\n State: Okay \r\n Pass: 1\r\n Read option: roundrobin (default)\r\n Write option: parallel (default)\r\n Size: 10486224 blocks\r\n\r\nd15: Submirror of d35\r\n State: Okay \r\n Size: 10486224 blocks\r\n Stripe 0:\r\n Device Start Block Dbase State Hot Spare\r\n c0t0d0s7 0 No Okay \r\n\r\n\r\nd25: Submirror of d35\r\n State: Okay \r\n Size: 10486224 blocks\r\n Stripe 0:\r\n Device Start Block Dbase State Hot Spare\r\n c0t3d0s7 0 No Okay \r\n\r\n\r\n用metareplace修復，依然報錯\r\n/usr/opt/SUNWmd/sbin/metareplace -e d30 c0t3d0s0\r\n# WARNING: md: d20: write error on /dev/dsk/c0t3d0s0\r\nWARNING: md: d20: /dev/dsk/c0t3d0s0 needs maintenance\r\n\r\n懷疑硬盤故障，更換新硬盤，重裝操作系統，故障依然，非常茫然，求助各位大大��！\r\n\r\n# more /etc/vfstab\r\n#device device mount FS fsck mount mount\r\n#to mount to fsck point type pass at boot options\r\n#\r\n#/dev/dsk/c1d0s2 /dev/rdsk/c1d0s2 /usr ufs 1 yes -\r\nfd - /dev/fd fd - no -\r\n/proc - /proc proc - no -\r\n/dev/md/dsk/d31 - - swap - no -\r\n/dev/md/dsk/d30 /dev/md/rdsk/d30 / ufs 1 no logging\r\n/dev/md/dsk/d32 /dev/md/rdsk/d32 /usr ufs 1 no logging\r\n/dev/md/dsk/d33 /dev/md/rdsk/d33 /var ufs 1 no logging\r\n/dev/md/dsk/d35 /dev/md/rdsk/d35 /bak ufs 1 no logging\r\n/dev/md/dsk/d34 /dev/md/rdsk/d34 /usr1 ufs 1 no logging\r\nswap - /tmp tmpfs - yes -\r\n\r\n系統補丁升級到105181-39，disksuite補丁到106627-11。\r\n另外，是在多用戶模式下！\r\n\r\n# who -r\r\n . run-level 3 Aug 15 19:18 3 0 S\r\n\r\n# df -k\r\nFilesystem kbytes used avail capacity Mounted on\r\n/dev/md/dsk/d30 2978534 32409 2886555 2% /\r\n/dev/md/dsk/d32 3095966 400349 2633698 14% /usr\r\n/proc 0 0 0 0% /proc\r\nfd 0 0 0 0% /dev/fd\r\n/dev/md/dsk/d33 1523574 121694 1340938 9% /var\r\nswap 716016 16 716000 1% /tmp\r\n/dev/md/dsk/d34 6191949 9 6130021 1% /usr1\r\n/dev/md/dsk/d35 5159318 9 5107716 1% /bak\r\n\r\n求助！搞了好幾天了：（

作者: tootooluu 時間: 2006-08-15 19:28
各位大人出來指點一下小弟��！

作者: susbin 時間: 2006-08-15 19:33
我不是大人，是小人。\r\ndisksuite 4.2 版本對 solaris 2.6 是不是太高了？

作者: tootooluu 時間: 2006-08-15 19:34
查了手冊，支持6的呀。。。。還是問人家討了半天才要到的4.2

作者: susbin 時間: 2006-08-15 19:46
在這壇子里搜一下吧，有些貼和你的問題差不多。

作者: tootooluu 時間: 2006-08-15 21:13
都看遍了啊，沒辦法才發的。用solaris 6也是沒辦法，用戶的應用程序是在6基礎上設計的，8不支持：（

作者: tootooluu 時間: 2006-08-15 21:47
謝謝樓上兄弟，這個帖子我看過了的，沒結果啊。。。能試的我都試過了，打算明天過去去FSCK 然后NEWFS去�。〉粔K是SUN剛發過來的新硬盤�。海�

作者: susbin 時間: 2006-08-15 22:05
“做鏡象，做完后同步一切正常，但一重啟動，就會出現某些分區needs maintenance”\r\n\r\n有幾個分區是要重啟后才能同步的吧。

作者: tootooluu 時間: 2006-08-15 22:58
不是的吧，我做玩，他自己就在同步，如果不重啟，同步狀態都是好的

作者: maike_xiao 時間: 2006-08-15 23:18
樓主能不能你把你做的步驟發上來讓大家看看？

作者: susbin 時間: 2006-08-16 00:13
/, /usr 都是要要重啟后才能同步。

作者: tootooluu 時間: 2006-08-16 08:36
問題是，我重啟動完，metareplace -e d30 c0t3d0s0，總是報錯：（

作者: wuqing 時間: 2006-08-16 09:01

原帖由 tootooluu 于 2006-8-16 08:36 發表\r\n問題是，我重啟動完，metareplace -e d30 c0t3d0s0，總是報錯：（

\r\n\r\n問題集中在以下三個分區:\r\n/\r\n/usr\r\n/var\r\n\r\n/dev/md/dsk/d30 /dev/md/rdsk/d30 / ufs 1 no logging\r\n/dev/md/dsk/d32 /dev/md/rdsk/d32 /usr ufs 1 no logging\r\n/dev/md/dsk/d33 /dev/md/rdsk/d33 /var ufs 1 no logging\r\n\r\n這三個分區的鏡像尤其是/分區其步驟和其他分區是不一樣的,給你一個參考樣例(SVM Administration Guide.pdf Page116-117):\r\n\r\nExample 11–6 SPARC: Creating a Mirror From the root (/) File System\r\n# metainit -fd 1 1 1 c0t0d0s0\r\nd1: Concat/Stripe is setup\r\n# metainit d2 1 1 c0t1d0s0\r\nd2: Concat/Stripe is setup\r\n# metainit d0 -m d1\r\nd0: Mirror is setup\r\n# metaroot d0\r\n# lockfs -fa\r\n# reboot\r\n...\r\n# metattach d0 d2\r\nd0: Submirror d2 is attached\r\n# ls -l /dev/dsk/c0t1d0s0\r\nlrwxrwxrwx 1 root root 88 Feb 8 15:51 /dev/rdsk/c1t3d0s0 ->\r\n../../devices/pci@1f,0/pci@1,1/ide@3/dad@0,0:a\r\n# init 0\r\n\r\n.\r\n.\r\nok nvalias backup_root /pci@1f,0/pci@1,1/ide@3/disk@0,0:a\r\nok setenv boot-device disk backup_root net\r\nok nvstore\r\n\r\nIn this example, the -f option forces the creation of the first RAID-0 volume, d1, which contains the mounted root (/) file system on /dev/dsk/c0t0d0s0. The second concatenation, d2, is created from /dev/dsk/c0t1d0s0. This slice must be the same size as, or larger than the size of d1. The metainit command with the -m option creates the one-way mirror d0 using the concatenation that contains root (/).\r\n\r\nNext, the metaroot command edits the /etc/vfstab and /etc/system files so that the system can be booted with the root (/) file system on a volume. It is a good idea to run the lockfs -fa command before rebooting. For more information, see the lockfs(1M) man page.\r\n\r\nDo not attach the second submirror before the system is rebooted. You must reboot after running the metaroot command and before attaching the second submirror.\r\n\r\nAfter a reboot, the submirror d2 is attached to the mirror, causing a mirror resynchronization. The system confirms that the concatenations and the mirror are set up, and that submirror d2 is attached.\r\n\r\nThe ls -l command is run on the root raw device to determine the path to the alternate root device in case the system might later need to be booted from it.

作者: wuqing 時間: 2006-08-16 09:05
/var 分區也是比較特別的,就是總是在不停地記錄日志,這個也只有在單用戶的模式下才可能同步數據\r\n最好是把你做這三個分區鏡像的步驟貼出來,大家才好分析是什么原因\r\n\r\n和硬盤沒有關系,20G的小硬盤還是很皮實的,更何況是新盤.步驟大體上沒有問題,畢竟還有2個鏡像是Okay狀態嘛\r\n\r\n注意:給的例子是Solaris10 SVM Administration Guide中的,僅供參考

作者: alex_linux 時間: 2006-08-16 09:41
Needs maintenance 如果同步還出現得話，建議將mirror打掉重做，還要徹底打點，光metadetach是不行得，用metaclear －f 清楚狀態，然后做mirror。\r\n問題基本差不多OK。。

作者: john.you 時間: 2006-08-16 09:44
找SDS for Solaris 2.6的軟件來用。

作者: tootooluu 時間: 2006-08-16 11:12
謝謝各位，我的這三個分區操作步驟如下：\r\nmetainit -f d10 1 1 c0t0d0s0 \r\nmetainit -f d20 1 1 c0t3d0s0\r\nmetainit d30 -m d10\r\nmetaroot d30\r\n查看/etc/vfstab，并且能看到“/”文件系統將被掛載到/dev/md/dsk上而不是掛載到/dev/dsk. \r\nmetainit -f d12 1 1 c0t0d0s4\r\nmetainit -f d22 1 1 c0t3d0s4\r\nmetainit d32 -m d12\r\nmetainit -f d13 1 1 c0t0d0s5\r\nmetainit -f d23 1 1 c0t3d0s5\r\nmetainit d33 -m d13\r\n。。。。\r\n編寫/etc/vfstab表\r\nlockfs -fa \r\ninit 6\r\n追加第二個鏡像設備到鏡像\r\nmetattach d32 d22\r\nmetattach d33 d23\r\n.....\r\ninstallboot /usr/platform/`uname -i`/lib/fs/ufs/bootblk /dev/rdsk/c0t3d0s0\r\nok setenv boot-device disk disk3\r\nok reset-all\r\n基本步驟就是這些了\r\nalex_linux朋友，說的metaclear我沒試過\r\n我是這么修復的：\r\n /usr/opt/SUNWmd/sbin/metadetach -f d30 d20\r\n fsck -y /dev/md/rdsk/d20\r\n /usr/opt/SUNWmd/sbin/metadetach -f d33 d23\r\n fsck -y /dev/md/rdsk/d23\r\n /usr/opt/SUNWmd/sbin/metadetach -f d32 d22\r\n fsck -y /dev/md/rdsk/d22\r\n \r\n /usr/opt/SUNWmd/sbin/metattach d30 d20\r\n /usr/opt/SUNWmd/sbin/metattach d33 d23\r\n /usr/opt/SUNWmd/sbin/metattach d32 d22\r\n\r\n結果依然報錯，\r\nWARNING: md: d22: write error on /dev/dsk/c0t3d0s4\r\nWARNING: md: d22: /dev/dsk/c0t3d0s4 needs maintenance\r\nmetaclear －f 能說的清楚點嗎？SUN 800建議我裝一下solaris 8看看是不是硬件問題！\r\n而且我每次拆鏡像完后，fsck總能發現有壞的地方，需要支持：）

作者: tootooluu 時間: 2006-08-16 11:15
還有就是：\r\nmetareplace -e d30 c0t3d0s0\r\nmetareplace -e d32 c0t3d0s4\r\nmetareplace -e d33 c0t3d0s5\r\n\r\n也報同樣的錯誤�。海�

作者: tootooluu 時間: 2006-08-16 11:41
剛剛做了如下操作：\r\n# /usr/opt/SUNWmd/sbin/metadetach -f d30 d20\r\nd30: submirror d20 is detached\r\n# /usr/opt/SUNWmd/sbin/metaclear -f d30 d20\r\nmetaclear: sun04: d30: metadevice is open\r\n\r\nd20: Concat/Stripe is cleared\r\n\r\n# /usr/opt/SUNWmd/sbin/metainit -f d20 1 1 c0t3d0s0\r\nd20: Concat/Stripe is setup\r\n# /usr/opt/SUNWmd/sbin/metattach d30 d20\r\nd30: submirror d20 is attached\r\n\r\n同步到73%的時候出錯：（

作者: 孤城 時間: 2006-08-16 13:47
不會是硬盤有問題了吧,做之前先fsck看看

作者: tootooluu 時間: 2006-08-16 14:50
樓上這篇我也看過，但情況不完全一樣啊，我的進程起來的呀。。。而且，它上面說是兩個盤都Needs maintenance。

作者: hjp1973 時間: 2006-08-16 18:06

原帖由 tootooluu 于 2006-8-15 19:23 發表\r\n# more /etc/vfstab\r\n#device device mount FS fsck mount mount\r\n#to mount to fsck point type pass at boot options\r\n#\r\n#/dev/dsk/c1d0s2 /dev/rdsk/c1d0s2 /usr ufs 1 yes -\r\nfd - /dev/fd fd - no -\r\n/proc - /proc proc - no -\r\n/dev/md/dsk/d31 - - swap - no -\r\n/dev/md/dsk/d30 /dev/md/rdsk/d30 / ufs 1 no logging\r\n/dev/md/dsk/d32 /dev/md/rdsk/d32 /usr ufs 1 no logging\r\n/dev/md/dsk/d33 /dev/md/rdsk/d33 /var ufs 1 no logging\r\n/dev/md/dsk/d35 /dev/md/rdsk/d35 /bak ufs 1 no logging\r\n/dev/md/dsk/d34 /dev/md/rdsk/d34 /usr1 ufs 1 no logging\r\nswap - /tmp tmpfs - yes -\r\n

\r\n\r\nSolaris2.6文件系統不支持logging選項,應改為\"-\",然后重起系統在看看!

作者: www326yu 時間: 2006-08-17 08:35
還有個可能就是用戶的母盤，也就原來的用戶自己的系統盤就是有問題的，當你鏡像同步時鏡像盤讀到原盤某個有問題的block時無法讀出數據也就不能完成同步，所以你每次做完同步后都會看到系統提示需要Needs maintenance

作者: scsi 時間: 2006-08-17 16:57
messages文件有什么報錯沒有？

作者: tootooluu 時間: 2006-08-17 23:43
謝謝各位支持！現在問題已經解決，又問SUN公司調了一個新盤，一次成功！重啟了幾次，都沒問題！\r\n可能是之前兩個盤P/N號一樣，但盤的容量還是有細微的差別導致吧，說不清楚：）謝謝各位了！

作者: Barrfee 時間: 2006-08-18 00:18
問題有幾種可能：\r\n1、系統根本沒有啟動到多用戶下面：\r\nwho -r 顯示不一定特別準確，需要自己判斷\r\n\r\n2、軟件本身存在文件損壞，如果有興趣的話，可以自己校驗一下\r\n\r\n3、補丁的問題，可能性不大\r\n\r\n4、硬盤的firmware版本不對\r\n\r\n5、還有是硬盤的firmware的型號不匹配，尤其對于OBP版本比較低的硬件。\r\n\r\n6、啟動腳本存在問題，可能性也不大。\r\n\r\n最終建議：比較更換前后主機運行環境的差別。\r\n\r\n該結貼了。

作者: tootooluu 時間: 2006-08-18 10:51
感謝大家支持，把操作步驟整理了一下，貼上來：）\r\n\r\n安裝Disksuite 4.2\r\n\r\n1 SUNWmd Solstice DiskSuite\r\n (sparc) 4.2,REV=1998.02.09.12.47.28\r\n 2 SUNWmdg Solstice DiskSuite Tool\r\n (sparc) 4.2,REV=1998.14.09.08.19.32\r\n 3 SUNWmdn Solstice DiskSuite Log Daemon\r\n (sparc) 4.2,REV=1998.02.09.12.47.28\r\n\r\n選擇1，2，3，在安裝過程中全部選“y”\r\n全部安裝成功后 init 6 重啟機器。\r\n\r\n# prtvtoc /dev/rdsk/c0t0d0s2 | fmthard -s - /dev/rdsk/c0t3d0s2\r\nfmthard: New volume table of contents now in place.\r\n# /usr/opt/SUNWmd/sbin/metadb -a -f -c 3 /dev/dsk/c0t0d0s3 /dev/dsk/c0t3d0s3\r\n\r\n# /usr/opt/SUNWmd/sbin/metainit -f d10 1 1 c0t0d0s0\r\nd10: Concat/Stripe is setup\r\n# /usr/opt/SUNWmd/sbin/metainit -f d20 1 1 c0t3d0s0\r\nd20: Concat/Stripe is setup\r\n# /usr/opt/SUNWmd/sbin/metainit d30 -m d10\r\nd30: Mirror is setup\r\n# /usr/opt/SUNWmd/sbin/metaroot d30 \r\n\r\n# /usr/opt/SUNWmd/sbin/metainit -f d11 1 1 c0t0d0s1\r\nd11: Concat/Stripe is setup\r\n# /usr/opt/SUNWmd/sbin/metainit -f d21 1 1 c0t3d0s1\r\nd21: Concat/Stripe is setup\r\n# /usr/opt/SUNWmd/sbin/metainit d31 -m d11\r\nd31: Mirror is setup\r\n# /usr/opt/SUNWmd/sbin/metainit -f d12 1 1 c0t0d0s4\r\nd12: Concat/Stripe is setup\r\n# /usr/opt/SUNWmd/sbin/metainit -f d22 1 1 c0t3d0s4\r\nd22: Concat/Stripe is setup\r\n# /usr/opt/SUNWmd/sbin/metainit d32 -m d12\r\nd32: Mirror is setup\r\n# /usr/opt/SUNWmd/sbin/metainit -f d13 1 1 c0t0d0s5\r\nd13: Concat/Stripe is setup\r\n# /usr/opt/SUNWmd/sbin/metainit -f d23 1 1 c0t3d0s5\r\nd23: Concat/Stripe is setup\r\n# /usr/opt/SUNWmd/sbin/metainit d33 -m d13\r\nd33: Mirror is setup\r\n# /usr/opt/SUNWmd/sbin/metainit -f d14 1 1 c0t0d0s6\r\nd14: Concat/Stripe is setup\r\n# /usr/opt/SUNWmd/sbin/metainit -f d24 1 1 c0t3d0s6\r\nd24: Concat/Stripe is setup\r\n# /usr/opt/SUNWmd/sbin/metainit d34 -m d14\r\nd34: Mirror is setup\r\n# /usr/opt/SUNWmd/sbin/metainit -f d15 1 1 c0t0d0s7\r\nd15: Concat/Stripe is setup\r\n# /usr/opt/SUNWmd/sbin/metainit -f d25 1 1 c0t3d0s7\r\nd25: Concat/Stripe is setup\r\n# /usr/opt/SUNWmd/sbin/metainit d35 -m d15\r\nd35: Mirror is setup\r\n\r\n# vi /etc/vfstab\r\n#device device mount FS fsck mount mount\r\n#to mount to fsck point type pass at boot options\r\n#\r\n#/dev/dsk/c1d0s2 /dev/rdsk/c1d0s2 /usr ufs 1 yes -\r\nfd - /dev/fd fd - no -\r\n/proc - /proc proc - no -\r\n/dev/md/dsk/d31 - - swap - no -\r\n/dev/md/dsk/d30 /dev/md/rdsk/d30 / ufs 1 no -\r\n/dev/md/dsk/d34 /dev/md/rdsk/d34 /usr ufs 1 no -\r\n/dev/md/dsk/d32 /dev/md/rdsk/d32 /var ufs 1 no -\r\n/dev/md/dsk/d35 /dev/md/rdsk/d35 /export/home ufs 2 yes \r\n-\r\n/dev/md/dsk/d33 /dev/md/rdsk/d33 /opt ufs 2 yes -\r\nswap - /tmp tmpfs - yes -\r\n\r\n# /usr/opt/SUNWmd/sbin/metainit hsp001\r\nhsp001: Hotspare pool is setup\r\n# lockfs -fa \r\n#init 6\r\n\r\n# /usr/opt/SUNWmd/sbin/metattach d30 d20\r\nd30: submirror d20 is attached\r\n# /usr/opt/SUNWmd/sbin/metattach d31 d21 \r\nd31: submirror d21 is attached\r\n# /usr/opt/SUNWmd/sbin/metattach d32 d22\r\nd32: submirror d22 is attached\r\n# /usr/opt/SUNWmd/sbin/metattach d33 d23\r\nd33: submirror d23 is attached\r\n# /usr/opt/SUNWmd/sbin/metattach d34 d24\r\nd34: submirror d24 is attached\r\n# /usr/opt/SUNWmd/sbin/metattach d35 d25\r\nd35: submirror d25 is attached\r\n\r\n#installboot /usr/platform/`uname -i`/lib/fs/ufs/bootblk /dev/rdsk/c0t3d0s0\r\n\r\nok setenv boot-device disk disk3 \r\nok reset-all

作者: tootooluu 時間: 2006-08-18 10:54
目前狀態：\r\n# /usr/opt/SUNWmd/sbin/metastat\r\nd30: Mirror\r\n Submirror 0: d10\r\n State: Okay \r\n Submirror 1: d20\r\n State: Okay \r\n Pass: 1\r\n Read option: roundrobin (default)\r\n Write option: parallel (default)\r\n Size: 6086304 blocks\r\n\r\nd10: Submirror of d30\r\n State: Okay \r\n Size: 6086304 blocks\r\n Stripe 0:\r\n Device Start Block Dbase State Hot Spare\r\n c0t0d0s0 0 No Okay \r\n\r\n\r\nd20: Submirror of d30\r\n State: Okay \r\n Size: 6086304 blocks\r\n Stripe 0:\r\n Device Start Block Dbase State Hot Spare\r\n c0t3d0s0 0 No Okay \r\n\r\n\r\nd31: Mirror\r\n Submirror 0: d11\r\n State: Okay \r\n Submirror 1: d21\r\n State: Okay \r\n Pass: 1\r\n Read option: roundrobin (default)\r\n Write option: parallel (default)\r\n Size: 1049328 blocks\r\n\r\nd11: Submirror of d31\r\n State: Okay \r\n Size: 1049328 blocks\r\n Stripe 0:\r\n Device Start Block Dbase State Hot Spare\r\n c0t0d0s1 0 No Okay \r\n\r\n\r\nd21: Submirror of d31\r\n State: Okay \r\n Size: 1049328 blocks\r\n Stripe 0:\r\n Device Start Block Dbase State Hot Spare\r\n c0t3d0s1 0 No Okay \r\n\r\n\r\nd32: Mirror\r\n Submirror 0: d12\r\n State: Okay \r\n Submirror 1: d22\r\n State: Okay \r\n Pass: 1\r\n Read option: roundrobin (default)\r\n Write option: parallel (default)\r\n Size: 6291936 blocks\r\n\r\nd12: Submirror of d32\r\n State: Okay \r\n Size: 6291936 blocks\r\n Stripe 0:\r\n Device Start Block Dbase State Hot Spare\r\n c0t0d0s4 0 No Okay \r\n\r\n\r\nd22: Submirror of d32\r\n State: Okay \r\n Size: 6291936 blocks\r\n Stripe 0:\r\n Device Start Block Dbase State Hot Spare\r\n c0t3d0s4 0 No Okay \r\n\r\n\r\nd33: Mirror\r\n Submirror 0: d13\r\n State: Okay \r\n Submirror 1: d23\r\n State: Okay \r\n Pass: 1\r\n Read option: roundrobin (default)\r\n Write option: parallel (default)\r\n Size: 3145968 blocks\r\n\r\nd13: Submirror of d33\r\n State: Okay \r\n Size: 3145968 blocks\r\n Stripe 0:\r\n Device Start Block Dbase State Hot Spare\r\n c0t0d0s5 0 No Okay \r\n\r\n\r\nd23: Submirror of d33\r\n State: Okay \r\n Size: 3145968 blocks\r\n Stripe 0:\r\n Device Start Block Dbase State Hot Spare\r\n c0t3d0s5 0 No Okay \r\n\r\n\r\nd34: Mirror\r\n Submirror 0: d14\r\n State: Okay \r\n Submirror 1: d24\r\n State: Okay \r\n Pass: 1\r\n Read option: roundrobin (default)\r\n Write option: parallel (default)\r\n Size: 12583872 blocks\r\n\r\nd14: Submirror of d34\r\n State: Okay \r\n Size: 12583872 blocks\r\n Stripe 0:\r\n Device Start Block Dbase State Hot Spare\r\n c0t0d0s6 0 No Okay \r\n\r\n\r\nd24: Submirror of d34\r\n State: Okay \r\n Size: 12583872 blocks\r\n Stripe 0:\r\n Device Start Block Dbase State Hot Spare\r\n c0t3d0s6 0 No Okay \r\n\r\n\r\nd35: Mirror\r\n Submirror 0: d15\r\n State: Okay \r\n Submirror 1: d25\r\n State: Okay \r\n Pass: 1\r\n Read option: roundrobin (default)\r\n Write option: parallel (default)\r\n Size: 10486224 blocks\r\n\r\nd15: Submirror of d35\r\n State: Okay \r\n Size: 10486224 blocks\r\n Stripe 0:\r\n Device Start Block Dbase State Hot Spare\r\n c0t0d0s7 0 No Okay \r\n\r\n\r\nd25: Submirror of d35\r\n State: Okay \r\n Size: 10486224 blocks\r\n Stripe 0:\r\n Device Start Block Dbase State Hot Spare\r\n c0t3d0s7 0 No Okay \r\n\r\n\r\nhsp001: is empty

作者: tootooluu 時間: 2006-08-18 10:55
---------OVER--------\r\n\r\n謝謝大家支持

歡迎光臨 Chinaunix (http://www.72891.cn/)