Drive element #500 firmware rev.:53Y2
Drive element #501 firmware rev.:53Y2
--- DEVICE ID's ---
Library bus address : lib device id = 0
Drive element #500 bus address:1
Drive element #501 bus address:2
------- NETWORK SETTINGS -------
Library IP : 10.40.3.99
Library Subnet Mask : 255.255.252.000
Library IP Gateway : 10.40.1.252
------- SNMP Agent -------
enabled - false
port - 161
community - public
grace period - 5 minutes
------- SNMP Recipients -------
------- JAVA PLUGIN CONFIGURATION -------
Java version 1.6.0_15
Java vendor Sun Microsystems Inc.
OS name Windows XP
OS version 5.1
OS architecture x86
------- DRIVE INFORMATION -------
Drive serial number : 1110348653
Drive firmware rev. : 53Y2
Drive vendor : IBM
Drive Model : LTO2 ULTRIUM
Drive Element ID : 500
Drive ID : 1
Drive Row : 0
Drive Column : 0
Drive State : Drive Loaded
Tape : label 100028 * type LTO ULTRIUM 2
Drive Put Retries : 6
Drive Get Retries : 255
Drive Mount Count : 7021
Idle Seconds : 105782139
Drive In Use Stats
Minimum : 34
30 sec - 5 min : 4200
5 min - 10 min : 1212
10 min - 30 min : 760
30 min - 60 min : 375
Maximum : 440
Drive serial number : 1110349176
Drive firmware rev. : 53Y2
Drive vendor : IBM
Drive Model : LTO2 ULTRIUM
Drive Element ID : 501
Drive ID : 2
Drive Row : 1
Drive Column : 0
Drive State : Drive Loaded
Tape : label 100029 * type LTO ULTRIUM 2
Drive Put Retries : 1
Drive Get Retries : 255
Drive Mount Count : 5743
Idle Seconds : 100880964
Drive In Use Stats
Minimum : 25
30 sec - 5 min : 3501
5 min - 10 min : 930
10 min - 30 min : 652
30 min - 60 min : 320
Maximum : 315
------- TAPE INFORMATION -------
------- TAPE CAP INFORMATION -------
Element Range :10 to 14
element id label tape type
---------- ----- ---------
------- TAPE PLAYGROUND INFORMATION -------
Element Range :10001 to 10002
element id label tape type
---------- ----- ---------
10002 CLNU01 UNIV LTO CLEAN
------- TAPE DRIVE INFORMATION -------
Element Range :500 to 501
element id label tape type
---------- ----- ---------
501 100029 LTO ULTRIUM 2
500 100028 LTO ULTRIUM 2
------- TAPE CELL INFORMATION -------
Element Range :1000 to 1039
------------- FSC # 3e24 (hex) --------------
MECHANISM : DRV0
OCCURRENCES : 140
LAST OCCURRENCE : 4/12/2010
: 15:53:44
:
SUMMARY : DRV Wait for Rewind Failed - Loaded State reported during wait.
TEXT : DRV Wait for Rewind Failed - Loaded State reported during wait.
------------- FSC # 3e24 (hex) --------------
MECHANISM : DRV1
OCCURRENCES : 111
LAST OCCURRENCE : 4/12/2010
: 15:53:25
:
SUMMARY : DRV Wait for Rewind Failed - Loaded State reported during wait.
TEXT : DRV Wait for Rewind Failed - Loaded State reported during wait.
------------- FSC # 3007 (hex) --------------
MECHANISM : NONE
OCCURRENCES : 47
LAST OCCURRENCE : 4/12/2010
: 15:24:18
:
SUMMARY :
TEXT : The library has started an IPL either by reset or power cycle.
------------- FSC # 3087 (hex) --------------
MECHANISM : REACH
OCCURRENCES : 3758
LAST OCCURRENCE : 12/21/2009
: 10:36:10
:
SUMMARY : An excessive position error was detected during motion.
TEXT : An excessive position error was detected during motion
Refer to specific FRU callouts for mechanism indicated.
Check robotic cabling connections and condition.
Check for any robotic obstructions.
Check z flex cabling connections and condition.
------------- FSC # 3490 (hex) --------------
MECHANISM : DC_PWR
OCCURRENCES : 8
LAST OCCURRENCE : 11/15/2009
: 15:12:23
:
SUMMARY : A power supply module has failed.
TEXT : The hardware detected a power supply failure. The unit's display will
flash a warning LED until the power supply has been serviced/replaced.
------------- FSC # 3381 (hex) --------------
MECHANISM : NONE
OCCURRENCES : 8
LAST OCCURRENCE : 9/24/2009
: 11:13:36
:
SUMMARY : Camera unable to find target.
TEXT : Camera could not find expected target. If this error occurs during
its first initilization then the machine is probably not configured
properly. This can be rectified by noting the cartridge location
of the cells inside the library and adjusting the theta endstops
appropriately.
This error is normal if CAP magazines are absent during a CAP audit.
It could also be caused by the tape drives not being installed,
latched or having a target.
------------- FSC # 3329 (hex) --------------
MECHANISM : NONE
OCCURRENCES : 8
LAST OCCURRENCE : 9/24/2009
: 11:13:36
:
SUMMARY : Unable to read a cartridge label or calibration target after three reads.
TEXT : Three retries were exausted trying in vain to read a cartridge label
or a calibration target.
If the cartridge is not labeled, this is not a true error.
If the customer uses unlabeled cartridges in their library this error
will appear frequently.
Also check for upside down cartridges or labels.
If numerous locations are failing it could possibly be that the
proimity sensor or camera are not working and the hand assembly
should be switched.
------------- FSC # 3311 (hex) --------------
MECHANISM : NONE
OCCURRENCES : 24
LAST OCCURRENCE : 9/24/2009
: 11:13:35
:
SUMMARY : Unable to read a calibration target.
TEXT : When scanning down past a calibration target the target was
unable to be de-coded. Three re-trys are done on each unreadable
target so unless all retries are logged as failures no action
should be taken. If numerous targets are failing it is likely
that the hand assembly needs to be replaced.
------------- FSC # 3788 (hex) --------------
MECHANISM : CAP
OCCURRENCES : 10
LAST OCCURRENCE : 9/24/2009
: 11:13:12
:
SUMMARY : The CAP could not be opened. Check for obstacles and proper connections.
TEXT : The CAP could not be opened. Check for obstacles and proper connections.
Make sure nothing is in front of the CAP Door preventing opening.
The robot opens the L40/80 CAP so check for Hand/Theta/Z errors.
If the CAP Door is open the CAP open sensor may be bad.
------------- FSC # 309e (hex) --------------
MECHANISM : NONE
OCCURRENCES : 24
LAST OCCURRENCE : 9/23/2009
: 17:21:44
:
SUMMARY : Cartridge access door is open.
TEXT : Cartridge access door is open.
All robot activity in the library has been aborted.
First confirm the doors are closed and aligned correctly before
proceeding with FRU replacements. Check the interlock cable condition.
------------- FSC # 3e25 (hex) --------------
MECHANISM : DRV1
OCCURRENCES : 4
LAST OCCURRENCE : 8/27/2009
: 14:47:15
:
SUMMARY : DRV Wait for Rewind Failed - Loading State reported during wait.
TEXT : DRV Wait for Rewind Failed - Loading State reported during wait.
------------- FSC # 428a (hex) --------------
MECHANISM : DRV0
OCCURRENCES : 3
LAST OCCURRENCE : 8/27/2009
: 12:47:59
:
SUMMARY : Drive has been successfully cleaned with a cleaning cartridge. This is
an informational fsc only.
TEXT : A drive has been successfully cleaned with a cleaning cartridge. This
is an informational fsc only and indicates that no error has occurred.
------------- FSC # 3b16 (hex) --------------
MECHANISM : NONE
OCCURRENCES : 108
LAST OCCURRENCE : 8/27/2009
: 12:40:41
:
SUMMARY : Destination drive is full
TEXT : The destination drive for the move is full.
------------- FSC # 308e (hex) --------------
MECHANISM : REACH
OCCURRENCES : 62
LAST OCCURRENCE : 12/21/2008
: 5:49:38
:
SUMMARY : The mechanism was unable to settle into the desired stoplock window
TEXT : The mechanism was unable to settle into the desired stoplock window
Refer to specific FRU callouts for mechanism indicated.
Check for obstructions to the mechanism.
Check belt tensions.
Confirm all screws for that mechanism are tightened properly and that
there is no unusual play or slop in the mechanism.
------------- FSC # 321c (hex) --------------
MECHANISM : DRV1
OCCURRENCES : 15
LAST OCCURRENCE : 12/21/2008
: 5:49:8
:
SUMMARY : Exhausted retries trying to remove the cartridge from the drive.
TEXT : The library exhausted the number of put back retries trying to remove
the cartridge from the drive.
------------- FSC # 428a (hex) --------------
MECHANISM : DRV1
OCCURRENCES : 7
LAST OCCURRENCE : 11/21/2008
: 15:38:33
:
SUMMARY : Drive has been successfully cleaned with a cleaning cartridge. This is
an informational fsc only.
TEXT : A drive has been successfully cleaned with a cleaning cartridge. This
is an informational fsc only and indicates that no error has occurred.
------------- FSC # 3204 (hex) --------------
MECHANISM : NONE
OCCURRENCES : 4836
LAST OCCURRENCE : 8/24/2008
: 3:10:38
:
SUMMARY : A retry was aborted because an error occurred.
TEXT : During preparation for retry, a failure was encountered.
Refer to prior failures for FRU isolation.
------------- FSC # 3207 (hex) --------------
MECHANISM : NONE
OCCURRENCES : 6
LAST OCCURRENCE : 8/24/2008
: 3:10:34
:
SUMMARY : The drive was full when it was expected to be empty.
TEXT : The cartridge drive is full.
------------- FSC # 3b14 (hex) --------------
MECHANISM : NONE
OCCURRENCES : 8
LAST OCCURRENCE : 8/23/2008
: 3:39:47
:
SUMMARY : Source drive is empty
TEXT : The source drive for the move is empty.
------------- FSC # 3206 (hex) --------------
MECHANISM : NONE
OCCURRENCES : 5
LAST OCCURRENCE : 8/23/2008
: 3:39:42
:
SUMMARY : The drive does not have a cartridge in it.
TEXT : The cartridge drive is empty.
End FSC's
------- GENERAL LIBRARY STATISTICS -------
Number of IPLs : 47
Number of Door Opens : 30
Uptime Seconds : 128115065
Moves : 25521
Mounts : 12775
Empty Reads : 621
Cap Gets : 1
Cap Puts : 3
Get Retries : 834
Get Failures : 2999
Put Retries : 7
Put Failures : 3
Label Retries : 0
Label Failures : 0
Label Reads : 2446
Target Retries : 38612
Target Failures : 9656
Target Reads : 1710
